The QEnergySpa Dilution Factor
This section contains theoretical information on the method used to optimize results with the QEnergySpa® depending on the dilution factor. None of the information shown should be held as fact. All percentages used herein are based on a water temperature of 27.1°C (approx 70° F). Please note that although this document describes optimal levels, for practical purposes we recommend using as much or as little water as you feel comfortable with, at the temperature that you prefer.
The dilution factor is determined by aspects such as the percentage of body mass immersed in the water compared to the amount of water used. Therefore, the lower the ratio between immersed body mass and volume of water in the bath, the higher overall body energy absorption you will obtain from the QEnergySpa®.BioEnergy Dilution Effect
Any part of the body which is not submerged into the water will be energized through the body part which is submerged. Therefore, the furthest point on the body away from the water is energized to a lesser and delayed extent. This dilution factor is gradual across the entire body. Where the dilution factor may become significant, would be in such instances where you wish to assist in the recovery of an injury, whether new or old. In this instance, it is recommended that you immerse that particular body part into the water for maximum benefit. Caution: avoid immersing an open wound due to the risk of infection.
| Figure 1, Bio-Energy Dilution Factor per body weight |
| Figure 1 – The diagram above indicates how the dilution factor decreases with more bodyweight immersed into the water with the QEnergySpa®. Immersing your whole body gives you no dilution or a ratio factor of 1:1. Whereas, inserting ½ of your body equates to a ratio of 1:2 or ½ dilution at your opposite extremities. | However, should you only insert your hands, then the dilution would become 1:83 at your opposite extremities? In short, in order to increase efficiency and the charge rate, we recommend that you maximize the percentage of your body mass in the water. |
The volume of Water Required
The efficiency of the QEnergySpa® is also dependent on the amount of water in relation to the amount of bodyweight you immerse. The ideal water volume to body weight is a ratio of 3.5 liters of water per kilogram of body weight.
Table 1, below and the corresponding chart in Figure 2, indicate how much water is recommended for full body immersion in relation to your weight, based upon the ‘ideal’ ratio listed above. Figure 3 however, indicates the desirable water volume for partial body immersion (e.g. your feet or hands) or smaller body masses (e.g. infants and pets).
| Optimal Volume of water required |
| ||||||
| Weight (Kg) | Volume of Water 3.5 l/Kg (Liters) | ||||||
| 0.5 | 1.75 | Water
The Source of All Life
Conserve our
| |||||
| 1 | 3.5 | ||||||
| 2 | 7.0 | ||||||
| 3 | 10.5 | ||||||
| 4 | 14.0 | ||||||
| 5 | 17.5 | ||||||
| 6 | 21.0 | ||||||
| 7 | 24.5 | ||||||
| 8 | 28.0 | ||||||
| 9 | 31.5 | ||||||
| 10 | 35 | ||||||
| 30 | 105 | ||||||
| 50 | 175 | ||||||
| 60 | 210 | ||||||
| 70 | 245 | ||||||
| 80 | 280 | ||||||
| 90 | 315 | ||||||
| 100 | 350 | ||||||
| 120 | 420 | ||||||
| 140 | 490 | ||||||
| 160 | 560 | ||||||
| 180 | 630 | ||||||
| 200 | 700 | ||||||
| Table 1, Volume of water per body weight. | |||||||
Calculate your ideal water volume in relation to |
What happens if the water volume per body weight exceeds the recommendations above?
Simply, the effectiveness would diminish, increasing the dilution factor. For example, if you were to immerse one foot in 7 liters of water and your foot weighed, say 2kg and your total body weight was 60kg, the dilution factor would be 1:30. That means that the Bio-Energy efficiency would be one 30th less at the opposite extremities of your body compared to the body part immersed. Therefore, if you weighed 120kg the dilution factor would be 60. If however, you were to immerse both your feet into the water, weighing says, 4kg and you were using 7 liters of water, your weight being 60kg, you would only have a dilution factor of 1:15 at the furthest point away from the immersed body part.
BioEnergy Dilution due to distance from the ORB itself
Q Tech Laboratories’ research indicates that the Q ENERGYspa® can energize water volumes up to 10,000 liters. Hence the effective radius of the ORB is approximately 1.2m. Outside this distance the water will still be energized through the domino effect from a water molecule to a water molecule, however, the effect will be diluted. Hence we recommend that you place the ORB near the middle of the tub and not near either end of the tub.
The QEnergySpa, BEFE Professional model 6000 is the best water-based bio-energy technology available, by the same electrical engineer who has worked on the Q technology for over 20 years. The latest improvements include increased EMF/RFI filtering, additional Q filtering technology, and additional Tesla filtering technology. The circuits are completely re-vamped for reduced heat and as such, fans are no longer required and for better energy flow, which is part of the Q technology.
See all of our QEnergySpa products. Go here.
Do you need spare parts for your QEnergySpa?
Genuine QEnergySpa Parts | QEnergySpa Footbath
Orb Ring and Track Sets | How to “Q”
Orbs and Cables | Array Cables | Fuses
Display all QEnergySpa Products Look here.
You may always contact us with any questions or part requests. We are here to help you set up your session. Nothing looks and performs like a genuine QEnergySpa Footbath. For that reason, Pros insist on them. Do you need spare parts for your QEnergySpa Footbath? Does your orb or array have a broken or missing part also? Then you have found the right place. Q2Spa.com Online Since 2002
Genuine QEnergySpa Parts | Orbs and Cables
Fuses | Array Parts | Orb Ring and Track Sets
Solid, untreated, unvarnished copper tubs
The statements on this site have not been evaluated by the FDA.
These products are not intended to treat, cure, or prevent any disease.