Posted on Leave a comment

Array Assembly Guide Instructions

Array Assembly Guide for Older QEnergySpa/BEFE Array 2000 Water Module

Befe Unit

Array 2000The Array Assembly Guide is for the Array 2000 (water module) was QtheExperience’s second mainstream Array, it was shipped with the B.E.F.E. power supply model numbers: 3006, 3024B, 3024D, and 2100’s.

 

Below is the step-by-step Array Assembly Instructions on how to change the Rings and Track.

Array FinalAre you still using an original import: The BEFE (Bio-Electric Field Enhancer)? Here are some instructions on how to replace the plates and track. Water conditions play a large role in the erosion of the positive plates and track. For this reason, it is very difficult to put a time frame on when to replace. The easiest way to determine when to change the positive plates and track is to take a close inspection. Place your finger on the positive plates and track, if it bends, replace it as the metal has deteriorated. When replacing plates or taking the ORB apart please read the manual carefully & check the ORB quick reference guide.

PLEASE NOTE:
When reassembling the Array (pictured) or the Orb, always ensure the top positive ring is sitting on and touching the Positive track. The cable connector hood is fitted flush with the orb. The diagrams below represent one of our initial array creations. However, the assembly is still the same.

Prior to Array assembly or disassembly:

Visually inspect each part in bright light. Look for cracks or any broken pieces on all acrylic and metal parts. Check the cable to be sure that it has no cracks, cuts, or crimps. Check for any abrasion on the cable. The QEnergySpa Array is a precise and fragile electronic piece of equipment. Because of its unique assembly, it is wise to assemble or disassemble in bright light. This will allow you to view the preciseness of each and every part prior to use.

It Helps To Be…

Careful. The care you take in the assembly or disassembly of these delicate precision instruments will preserve them for the years to come. Once you understand how fragile and precise the acrylic parts are, you will appreciate your patience spent on taking care of your QEnergySpa. It is also extremely important to assemble and disassemble DRY components. It’s easy to slip and mishandle the wet parts. They break easily. They are precision made to fit perfectly.

B.E.F.E. Array Assembly Guide

Array Assembly Step 1

Step 1

Remove the stainless steel track by un-clipping it from the

bottom positive ring. Swinging it outwards at an angle and

slide it downwards to remove it from the top acrylic plate.

 

 

 

 

Array Assembly Step 2

Step 2

Gently slide the removable leg out (it is safer and easier to

do this if the Array is on a table or flat surface). The 2 positive

rings (the degraded pair) may or may not come out with the leg

when you remove it. If not, gently slide them out horizontally.

 

 

Array Assembly Step 3

Step 3

Slot the new plates into the existing slots followed by gently sliding

the leg back into place. Be sure to align the plates correctly with the

appropriate slots in the other legs. If it does not go back together easily,

DO NOT force it! Double-check to make sure that the plates are seated

correctly and there are no obstructions.

 

 

Array Assembly Step 4

Step 4

Finally, slot the top of the track into the slot in the top of the Array.

As you slide it into place, the section marked “A” should be on top of

the top newly inserted plate and “B” should be underneath the bottom

newly inserted plate. The track should audibly click’ into place.

 

 

Array Assembly Step 5

Clipping Cable onto the Array

The end of the cable that attaches to the array has two

connectors or clips. The negative one is black in color

and round in shape. This fits onto the round rod located in

the center protruding from the top of the array. The other

is red and square. This fits onto the flat metal track on the

outside of the top of the Array.

 

Array Assembly Step 6

Completed Array Assembly

Are you still not sure and need some help? I am always available to help.

Please feel free to give me a call: Debbie at 303-782-4841

_______________________________

Do you need spare parts for your QEnergySpa?

Q2Spa.com | Genuine QEnergySpa Parts | QEnergySpa Footbath | Orb Ring and Track Sets

Orbs and Cables | Array Cables | Fuses | QEnergySpa, BEFE Consumables | Support

Does your QEnergySpa have a broken or missing part also? Then you have found the right place.

First of all, we have all parts to fit ALL BEFE and QEnergySpa models. In addition, the most asked for parts include replacement rings and tracks, cables, orb parts, orb shells, and orb buttons. We also offer all services including warranty and repair. Q2Spa.com also offers Certified Used Models to meet almost every budget. You may see all the Q2Spa.com used models, Go here.

Lastly, what is new at Q2Spa.com? Check out our Blog, look here.

Q2Spa| Genuine QEnergySpa Parts | Foot Bath Tips | Veggie Trials | BEFE Parts

The statements on this site have not been evaluated by the FDA.
These products are not intended to treat, diagnose, cure, or prevent any disease.

Leave a Reply